Waterford-appliances NATURAL GAS E61-LP Manuel d'utilisateur télécharger pdf (Page 16)

16 Waterford E61 Gas Fireplace Insert

OPERATING INSTRUCTIONS

COPY OF THE

LIGHTING PLATE INSTRUCTIONS

Gas Control Valve:

As the gas control valve turns ON and OFF, a

dull clicking sound may be audible, this is normal

operation of a gas regulator or valve.

Unit Body/Firebox:

Different types and thicknesses of steel will

expand and contract at different rates resulting

in some "cracking" and "ticking" sounds will be

heard throughout the cycling process.

MAINTENANCE

INSTRUCTIONS

1) Always turn off the gas valve before clean-

ing. For re-lighting, refer to lighting instruc-

tions. Keep the burner and control compart-

ment clean by brushing and vacuuming at

least once a year.

When cleaning the logs, use a clean soft

paint brush as the logs are fragile and easily

damaged.

2) Clean glass (never when unit is hot), appli-

ance, door and louvers with a damp cloth.

Never use an abrasive cleaner.

The heater is finished in a heat resistant

paint and should only be refinished with

heat resistant paint (not with wall paint).

Waterford uses Stove Brite Paint - Metallic

Black #6309.

3) Make a periodic check of burner for proper

position and condition. Visually check the

flame of the burner periodically, making

sure the flames are steady; not lifting or

floating. If there is a problem, call a qualified

service person.

4) The appliance and venting system must be

inspected before use, and at least annually,

by a qualified field service person, to en-

sure that the flow of combustion and ven-

tilation air is not obstructed.

During the annual service call, the burner

should be removed from the burner tray and

cleaned. Replace the embers but do not

block the pilot.

5) Verify proper operation after servicing.

6) Keep the area near the appliance clear and

free from combustible materials, gasoline

and other flammable vapours and liquids.

CAUTION: ANY SAFETY SCREEN

OR GUARD REMOVED FOR SERV-

ICING AN APPLIANCE MUST BE

REPLACED PRIOR TO OPERAT-

ING THE APPLIANCE.

TO TURN OFF GAS APPLIANCE

FOR YOUR SAFETY READ BEFORE LIGHTING

4) Push in control knob all the way and

hold in. Continually push and release

the black button on spark igniter until

pilot lights. Continue to hold the

control knob in for about 1/2 minute

after the pilot is lit. Release knob and

it will pop back up. Pilot should remain

lit. If it goes out, repeat steps 1) to 4).

If knob does not pop up when released,

stop and immediately call your service

technician or gas supplier. If the pilot will

not stay lit after several tries, turn the gas

control knob to “OFF” and call your

service technician or gas supplier.

STOP! Read the safety information

above on this label.

1) Push in gas control knob slightly and

turn clockwise to “OFF”. Knob

cannot be turned from “PILOT” to “OFF”

unless knob is pushed in slightly. Do

not force.

2) Wait five (5) minutes to clear out any

gas. If you then smell gas STOP! follow

“B” in the safety information above on

this label. If you don’t smell gas, go to

the next step.

3) Turn knob on gas control counter-

clockwise to“PILOT”.

1) Push in the gas control knob slightly and

turn clockwise to “OFF”. Do not force.

CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due

to high surface temperatures keep children, clothing and furniture, gasoline

and other liquids having fammable vapors away. Keep burner and control

compartment clean. See installation and operating instructions

accompanying appliance.

LIGHTING INSTRUCTIONS

5) Turn gas control knob

counterclock-wise

to “ON”.

6) Use rocker switch to op-

erate main burner.

A)This appliance has a pilot which

must be lighted by hand. When

lighting the pilot, follow these

instructions exactly.

B) BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some

gas is heavier than air and will settle

on the floor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance

- Do not touch any electric switch, do

not use any phone in your building

- Immediately call your gas supplier

from a neighbours phone. Follow the

gas supplier’s instructions.

- If you cannot reach your gas supplier,

call the fire department.

C)Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified

service technician. Force or attempted

repair may result in a fire or explosion.

D) Do not use this appliance if any part has

been under water. Immediately call a

qualified service technician to inspect the

appliance and to replace any part of the

control system and any gas control which

has been under water.

This appliance needs fresh air for safe

operation and must be installed so there are

provisions for adequate combustion and

ventilation air.

DO NOT REMOVE THIS INSTRUCTION PLATE

WARNING: If you do not follow these instructions exactly, a fire or

explosion may result causing property damage, personal injury or loss

of life. Improper installation, adjustment, alteration, service or maintenance

can cause injury or property damage. Refer to the owner’s information

manual provided with this appliance. For assistance or additional

information consult a qualified installer, service agency or gas supplier.

OFF

ELEMENT

THERMO-

ELECTRIQUE

VEILLEUSE

PILOT BURNER

THERMOPILE

908-017b

2) Turn off all electric power to the

appliance if service is to be performed.

You may shut off the pilot during prolonged non use periods to conserve fuel.

This appliance must be installed in accordance with local codes, if any; if none, follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation

Codes, CSA B149.1. (Australia: AG601, New Zealand: NZS 5261)

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Waterford-appliances NATURAL GAS E61-LP Manuel d'utilisateur Page 16

Commentaires sur ces manuels